WOODWARD PLC Module 8400-016 8440-1843 8516-038 PROACT Model II Speed Control Genset Controller Mechanical Turbine Governor TG-13

Product Description

WOODWARD PLC Module 8400-016 8440-1843 8516-038 PROACT Model II Speed Control Genset Controller Mechanical Turbine Governor TG-13 In Stock 

Product Description

8400-016

Features and Benefits
•High Accuracy: Provides precise speed control with an accuracy of ±0.25%.
•Wide Speed Range: Operates effectively from 0 to 6000 RPM.
•Fast Response: Achieves response times under 100 milliseconds to maintain stable speed.
•Robust Design: Built for durability in harsh environments with a wide operating temperature range of -40 to 85°C.
•Versatile Application: Suitable for engines, generators, pumps, and compressors.
•Improved Efficiency: Enhances machinery performance and helps reduce fuel consumption and emissions.
•Extended Equipment Life: Protects engines from overspeed/underspeed damage, reducing wear.
•Ease of Use: Simple to configure, operate, and install.

8440-1843

Technical Specifications
•Part Number: 8440-1843 (easYgen-3200-5-P2).
•Manufacturer: Woodward, Class 0.5 accuracy.
•Setting Range: 1 - 32,000 A.
•Protection: IP 20 enclosure with IP front sealing.
•Dimensions: 282W x 216H x 96D mm.
•Outputs: Isolated relay outputs.
FAQ
•Q1: What series does this controller belong to? 
   A1: It is part of the easYgen-3000 series.
•Q2: What are its key operation modes? 
   A2: It includes manual, auto, and load/no load test modes.
•Q3: What safety precautions are required? 
   A3: It must be installed in a low-static environment and operated only by certified professionals.

8516-038

The Woodward TG-13 (8516-038) is a digital regulator for precise engine speed and load control in harsh industrial environments, featuring robust IP65 protection and multi-protocol communication.

Technical Specifications & Parameters
•Operating Voltage: 18-36VDC.
•Operating Temperature: -40°C to +85°C.
•Enclosure Rating: Fully enclosed with IP65 protection.
•Processor: 32-bit high-performance microcontroller.
•Memory: Built-in EEPROM for parameter storage.
•Interfaces: Multiple analog/digital I/O channels.
•Communication: Supports RS-232, RS-485, and CAN bus.

Installation & Debugging Guide

• Site: Install in a well-ventilated, vibration-free area, ensuring proper cooling space.

• Wiring: Use correct wire sizes, secure connections, and prefer shielded cables for signals.

• Setup: Configure basic parameters (e.g., address, communication settings) via the front panel or configuration tool.

Operation & Maintenance Instructions

• Interface: Operate via the intuitive LCD menu; password protects critical changes.

• Routine Checks: Clean surfaces and check terminals quarterly; inspect internal components annually with power off.

• Faults: Use the built-in diagnostic codes and event logs for troubleshooting; contact professionals for complex issues.

TG-13 Governor

Installation of the TG-13 Governor

Installation of the TG-13 Governor
1. Install the drive gear from the mechanical governor on the TG-13 drive shaft, A spacer is shipped on the drive shaft and this must be left on the shaft between the gear and the governor. Use the new drive key which accompanies the TG-13.
Should the gear not slip onto the shaft, check carefully for burrs or dings in the inside diameter of the gear or in the keyway. Remove damaged areas with a stone or lightly hone the inside diameter of the gear, if necessary. The new drive key must slip freely in the drive keyway and in the TG-13 drive shaft keyway. 
 

 

2. With the spacer and gear in place with the new drive key on the TG-13 drive shaft, tighten the castle nut. The nut should be snug, but need not be torqued. Use the new cotter key to secure the castle nut.
3. Carefully install the new governor-drive assembly where the mechanical governor was removed. No gasket is required on the multi-cylinder mounting surface, although a thin gasket may be used to overcome imperfections in the mounting surface and to assure a good fit. The TG-13 installs with the clockwise output shaft toward the engine. Arrows on the side of the governor identify output-shaft rotation.
 Meshing the drive gear with the governor drive on the engine must be done carefully. Pressure must not be exerted while installing the governor. If the gear does not mesh, remove the governor and rotate the drive slightly, then try again. The installation must not require any more pressure than that exerted by the weight of the governor.
4. Tighten the set screw on the one cylinder engine. Evenly torque the four mounting bolts on the multi-cylinder unit.

Operation
Fill the governor with new, clean oil, If possible, use the same weight and grade of oil used in the engine oiler system. The engine oiler oil will work in almost all installations. The only exceptions may be in installations which wilt want to start an extremely cold governor. It is possible in these installations that a lighter (10 weight or 5 weight oil) may have to be used during the cold season. The governor will require about 1.750 quarts of oil. Remove the oil breather screw from the cover and fill through this hole. Add Oil until the oil level is visible in the sight gauge on the side of the governor. Always check the oil level before starting the engine. Add oil if it is not visible in the sight gauge. 
Figure 2. TG-13 Governor
Droop Adjustment
Adjustment of droop may be required during TG governor installation if the governor shows instability or is slow in responding to load change.
Instability in the form of hunting or surging indicates possible insufficient droop or insufficient terminal-shaft movement. If the terminal shaft is moving at least 20 degrees between minimum and maximum fuel, it may be necessary to increase droop. Delay in accepting load after a toad change indicates excessive droop.

To change the droop setting: shut down the engine; remove the governor cover, and move the adjusting lever as indicated. Do not move the droop-adjusting lever in the decrease direction too close to the center line of the terminal shaft. Move the lever about 0.8 mm (1/32 of an inch) at a time when adjusting droop. After each move replace the cover and try the operation at the new setting. 
Figure 4. Droop-Adjusting Lever Movement 

Whose sales picture

8516-038 image is for reference only product style, spec ific data of manufacture and product version, please refer to the actual product delivery!

FAQ

Q: Is your product new or refurbished?
A: All our products are original new with one year warranty.
Q: How many days the goods will arrive my hands if I place the order now?
A: As soon as we receive the payment, I will ship the products immediately.
It usually take 3-5 days from China to your hands.
Q: Could you give me some discount?
A: Contact Stella to get more discount for 8440-1843
Q:Can you ship the goods to my country?
A: Pls don't worry ,We can ship the goods to worldwide
Q:What payment mothod we used?
A:We usually use T/T (Telegraphic Transfer),and we can received with in 1-2days
Q:Can I contact you on Email?
A: You can contact me online to get my email add
Amikon sells automation equipment around the world. With a strong focus on older, obsolete, Automation parts, we pride ourselves in providing high quality parts and services to our customers. Our goal is to provide a seamless purchasing experience that trumps the competition. Low lead time, with quick shipping and processing is our utmost concern. Reducing downtime is extremely important to us and our customers take notice! All orders are prepared by our expertly-skilled team and thoroughly vetted before each shipment.

We are specialized in providing world-reknowed brands:  Even some discontinued ones.We pride ourselves on being a leading provider of industrial automation parts and solutions. Extensive Inventory, Competitive Pricing, Fast Delivery, Global Reach and serves a diverse range of industries with 12 month warranty. Contact us today to learn more about how we can support your business needs.

We have a large inventory of spare parts for industrial control systems. Manufacturers cover a wide range and also work with a wide range of suppliers.Fast shipping to provide you with the best solution to meet your urgent needs If we don't have the stock request quotation you need, You can contact help you.

Recommend

Woodward	8440-1750	Woodward	5453-203	Woodward	5462-744
Woodward	EASYGEN-1500-55B	Woodward	5437-672	Woodward	9907-164
Woodward	9905-003	Woodward	5464-210	Woodward	8271-467
Woodward	SA1509-24	Woodward	5466-353	Woodward	9905-068  2301A
Woodward	EASYGEN-2500-5	Woodward	5466-355	Woodward	9905-792
Woodward	9905-463	Woodward	5461-655	Woodward	CMW112
Woodward	5463-785	Woodward	5461-648	Woodward	8200-226
Woodward	5463-473	Woodward	5461-644	Woodward	EASYGEN-1000
Woodward	5464-414	Woodward	5462-718	Woodward	8440-1809
Woodward	5464-544	Woodward	9907-029	Woodward	9907-028
Woodward	5463-581	Woodward	5462-757	Woodward	5438-667
Woodward	5464-013	Woodward	5462-948	Woodward	5464-643
Woodward	5464-211	Woodward	5462-408	Woodward	5464-648
Woodward	5417-028	Woodward	5500-577	Woodward	5464-653
Woodward	5501-380	Woodward	5462-916	Woodward	5464-850
Woodward	5417-175	Woodward	5462-758B	Woodward	5466-026
Woodward	5417-040	Woodward	5461-650	Woodward	5466-352

Amikon sells new and surplus products and develops channels to purchase such products. This website is not approved or endorsed by any of the listed manufacturers or trademarks.
Amikon is not an authorized distributor, distributor or representative of the products displayed on this website. All product names, trademarks, brands and logos used on this website are the property of their respective owners. The description, description or sale of products with these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.